Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Roofing: The Orlando Owner’s Guide
CGI roofing parts in Orlando typically cost $400 – $1,800 installed for a repair, and most single-part swaps take under a day once we’ve matched your exact component. Homeowners usually find out a CGI part has failed the hard way: a rust-colored drip on the ceiling, a loose metal panel flapping after a windstorm, or a fastener that’s backed out and left a gap. You’re not shopping for a whole roof here – you need one part sourced, priced, and fixed correctly. That’s exactly what we handle at Sawyer Remodel Orlando.
Sawyer Remodel Orlando is an independent service provider, not affiliated with CGI. We stock common CGI fasteners, closures, and trim profiles on the truck, and we can source full panels from CGI’s Central Florida distribution network fast.
Which CGI Models This Applies To
CGI makes heavy-gauge residential and commercial metal roofing under a few series names you’ll find stamped on the back side of a removed panel or on the original permit paperwork: the Advantage and Slate lines for residential, and the heavier Wide Rib panels for commercial or shop buildings. The part you need has to match the panel’s profile exactly – a closure that fits a Wide Rib panel won’t seal an Advantage panel, and a fastener that’s too short won’t bite through a Slate panel’s thicker gauge.
Here’s the gotcha we see a lot in Orlando: CGI sells the same profile in different base metals. An aluminum panel and a galvanized steel panel from the same series take different fasteners and different closures. If you buy the wrong metal matchup and install it, you’ll get galvanic corrosion within a couple of Florida rain seasons. When you call us, we’ll match the panel by profile, gauge, and base metal – not just by what it looks like from the ground. If you still have a physical sample, measure the rib height and spacing; that plus the panel’s backside stamp gets us to the right part fast.
OEM CGI parts are worth the money for anything that touches the panel surface: closures, seam caps, and trim. For fasteners, a quality aftermarket equivalent with the same gauge, length, and coating rating works just as well and often costs less. We’ll tell you which is which on the estimate.
Styles & brands we work with
Signs Your CGI Roofing Is Failing
- Loose or backed-out fasteners. Metal roofs expand and contract with Florida heat, and over a decade that thermal cycling can work screws loose. The rubber washer under the screw head dries out, cracks, and stops sealing – which is how pinhole leaks start.
- Rust streaks running down from a specific area. This usually means a panel edge was cut in the field and the cut wasn’t treated. Orlando’s humidity turns those raw edges into rust lines within a season or two.
- Flapping or rattling during wind. A panel that moves means the fastener pattern has failed at the ribs. Ignore it, and the panel can tear off completely in the next summer thunderstorm.
- Daylight visible through the ridge cap or rake trim. Closures degrade, especially at the ridge. When the foam closure breaks down, you’ve got an open seam that lets wind-driven rain straight into the attic.
- Dark staining inside the attic on the underside of the decking. By the time it shows inside, the leak has been working for a while. Finding the entry point on a metal roof takes a good eye – water travels along purlins and drips far from where it entered.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For CGI roof repair in Orlando, you’re looking at $400 – $1,800 for most single-part replacements. A fastener resecure job with new washers runs at the low end. Replacing a section of ridge cap or rake trim lands in the middle. Swapping out a full metal panel runs toward the top of that range, and a detailed metal roof repair with multiple failed components lands around $2,500.
What moves the price: which part failed, how high and steep the roof is (single-story walkable roofs cost less in labor than a two-story cut-up roof requiring staging), and whether we need to pull adjacent panels to get the replacement seated right.
Every estimate from us is a written, line-item price before work starts. That number doesn’t change at the invoice unless you add scope. The workmanship is covered by our 365-Day Done Right Promise: if it’s not done right, we make it right. And if a repair fails within that year, your second visit is free, no argument.
DIY or Call Us?
Metal roof work is a mix of safe enough and genuinely not worth the hospital visit. You can safely grab binoculars and check for backed-out screws, missing closures, and visible rust from the ground. If you can reach the eave from a short ladder, a visual check of the gutter line is fine too.
What you shouldn’t do: get on a metal roof without proper footwear and fall protection, especially after a rain. Wet metal is slicker than most people expect, and Orlando afternoon storms love to roll in while you’re mid-project. Tightening old fasteners without replacing the washer just strips the hole and makes the leak worse. If the failed part is at the ridge or requires panel removal, that’s a two-person job with the right seam tools. Call (850) 809-0306. We’ll look it over, write the price down, and you can decide from there.
FAQs
A CGI metal roof in Orlando can last 40 – 50 years on the panel itself, but the fasteners, closures, and sealants realistically need attention every 15 – 20 years in our humidity and storm exposure. The panel doesn’t fail – the components around it do. Call (850) 809-0306 and we’ll inspect what’s failing before it becomes a ceiling stain.
Most CGI failures are repairable without replacing panels. Backed-out fasteners, damaged closures, and minor trim issues are component-level repairs that cost on the low end of the $400 – $1,800 Orlando range. We’ll only recommend panel replacement when the metal itself is torn, heavily rusted through, or the profile needs exact matching that’s no longer available.
Most single-part CGI repairs in Orlando are done in one visit, usually four to six hours from arrival to cleanup. If we need to order a specific panel or trim piece from CGI’s distribution network, that adds a few days of lead time, but the actual installation is still a single day of work.
We stock common CGI fasteners, closures, and ridge trim profiles on the truck. Full panels and long-run trim pieces are pulled same-week from CGI’s Central Florida distributors. Either way, the price is written and confirmed before any work starts. Call (850) 809-0306 for a free estimate.
Written by Luca Romano, Owner & Lead Contractor, Sawyer Remodel Orlando at Sawyer Remodel Orlando, serving Orlando and nearby areas.
