Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Bathroom Remodeling: The Orlando Owner’s Guide
Moen bathroom remodeling in Orlando typically costs between $9,000 and $28,000, and our crew stocks Moen-compatible trim kits, cartridges, and valve bodies so we can swap failed parts without waiting on a parts house. Most owners find us after a Moen shower valve starts dripping, the handle gets stiff, or the tub spout diverter stops holding. The part itself is usually under $75, but the labor to open a wall or re-tile around a valve is where cost climbs: expect $300 to $900 for a straightforward cartridge and trim replacement, and $2,500 to $9,000 if we are rebuilding the shower surround around the valve.
We are an independent Orlando contractor, not affiliated with Moen, but we install and service their fixtures on most of our bathroom remodels in College Park, Baldwin Park, Thornton Park, Winter Park, and the surrounding Orlando metro.
Key Takeaways
- Moen bathroom remodel ranges from $9,000 to $28,000 installed in Orlando.
- Cartridge-only replacement runs $300 to $900; full shower rebuild around the valve $2,500 to $9,000.
- Moen PosiTemp, Moentrol, and ExactTemp valves each take different cartridges and trim plates.
- Hard Orlando water kills Moen cartridges faster than anywhere in the U.S. – plan on 8 to 12 years per valve, not the 15-plus the packaging claims.
Which Moen Models This Applies To
Moen has three valve platforms you will see in Orlando bathrooms: PosiTemp (the most common, found in most Moen single-handle showers and tubs), Moentrol (older two-handle or single-handle pressure-balancing valves), and ExactTemp (the newer thermostatic line, used in higher-end Moen and some Grohe installs). Each takes a different cartridge: the PosiTemp 1222, the Moentrol 1225 or 1200, and the ExactTemp 1248. They do not interchange. If you unscrew the trim plate and see a brass stop on the valve body with “1222” stamped into the plastic stem, it’s a PosiTemp, and a Moentrol cartridge will not seat.
Identification without opening the wall: remove the handle and trim plate. The valve body will have a model number stamped on the brass or a sticker on the escutcheon back. If the plate is too corroded to read, a picture of the tile opening sent to us usually settles it. For OEM versus aftermarket: Moen cartridges are the only part we will install without a conversation. Aftermarket 1222 clones from Danco or Plumb Pak cost half as much and fail in 18 months. In a $9,000 to $28,000 Orlando bathroom remodel, that is false economy.
Trim kits are a different story. Quality finishes from Moen’s Voss, Align, and Genta lines drop straight onto PosiTemp valves, and we keep the most common Orlando seller, brushed nickel Voss trim, stocked on the truck. We also carry faucet trim kits for KraftMaid and Cambria vanity configurations when those brands are part of the scope.
Styles & brands we work with
Signs Your Moen Bathroom Remodeling Is Failing
- Drip after the handle is off. That is the 1222 cartridge letting water through the balancing spool. In Orlando’s hard water, calcium builds up on the spool and holds it open. Fix before the drip becomes a stream.
- Stiff or binding handle. Mineral scale has worked between the cartridge and valve body bore. Forcing it breaks the plastic stem and leaves the valve stuck in place. We use a Moen cartridge puller to remove it without gouging the brass.
- Sudden temperature swings when a toilet flushes. The PosiTemp pressure-balancing element has failed. You will see scald dips or cold blasts during regular use. This is the part Moen warranties for life specifically because it is designed to prevent scalding.
- Tub spout won’t hold shower mode. The diverter is worn or the spout o-ring has failed. On Moen tub spouts with a pull-up knob, the fix is a new spout, not a new valve, and it takes under an hour.
- Corrosion blooming on the trim plate. Orlando humidity plus chlorinated city water eats the finish on polished brass and oil-rubbed bronze first. The trim plate fails long before the valve. A new trim kit is $120 to $350 and bolts on in under two hours without touching the wall.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
| Scope | Orlando Installed Price |
|---|---|
| Cartridge replacement (PosiTemp 1222 / Moentrol / ExactTemp) | $300 – $900 |
| Trim kit replacement (plate, handle, spout, showerhead) | $250 – $550 |
| Tub spout replacement | $150 – $300 |
| Valve body replacement (requires wall or tile access) | $1,200 – $4,500 |
| Full Moen bathroom remodel (shower, tub, vanity, tile) | $9,000 – $28,000 |
The price spread depends on whether we are replacing a part or rebuilding the shower around it. A cartridge swap on an accessible shower wall runs the low end. A valve body replacement behind a tiled wall in an Orwin Manor bungalow means opening tile, replacing the valve, and re-setting the tile pattern, which lands at the high end. Every quote includes the Moen part, all labor, and our 365-Day Done Right Promise in writing. We also provide a written price before any work starts, so the number you approve is the number you pay.
DIY or Call Us?
You can safely check a few things on your own: whether the shutoff in the wall behind the shower works, whether the drip is coming from the spout or the handle, and whether the trim plate is cracked or just scuffed. That tells us a lot before we even arrive. What you should not do is pull a Moen cartridge out of a live valve without shutting off the house water. If the valve body is in an outside wall, and you leave it uncapped, you can flood the wall cavity before you get the new cartridge seated. The brass valve in an Orlando exterior wall sits right against hot, humid air half the year, and a small leak behind tile is not something you find until the baseboard swells.
If the job is a trim swap and the water shuts off cleanly, have at it. If the valve is older than 15 years, the cartridge is likely seized, and brute force without a Moen puller scores the bore and ruins the valve. That turns a $400 cartridge job into a $2,500 valve replacement fast. Call us at (850) 809-0306 and we will send a background-checked, uniformed technician with the parts already on the truck. Good work doesn’t need a speech, it just needs to hold up.
FAQs
Realistically, 8 to 12 years with Orlando’s hard water, despite Moen’s lifetime warranty on the cartridge itself. Scale and chlorine degrade the balancing spool, and most cartridges we pull in College Park and Winter Park homes are between 9 and 11 years old. Call (850) 809-0306 for a replacement quote.
Yes, in most cases. If the valve body brass is intact, we replace the cartridge, seats, and springs, which restores sealing without replacing the valve. If the bore is scored or the valve is weeping at the solder joint, replacement is the honest answer. Call us and we will tell you which situation you have before any work begins.
One to two hours for a straightforward replacement, including shutoff, pull, clean, reseat, and testing. If the trim plate is corroded and needs replacement at the same time, add 45 minutes. We book Moen repairs with a live arrival time so you are not home all day waiting.
We stock the Moen 1222 PosiTemp cartridge, the 1255 Moentrol, common Voss and Align trim kits, tub spouts, and showerheads. Less common ExactTemp parts come from our Orlando supplier same day. If we have to order, we tell you before you approve the work.
Written by Luca Romano, Owner & Lead Contractor, Sawyer Remodel Orlando at Sawyer Remodel Orlando, serving Orlando and nearby areas.
