Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Roofing: The Orlando Owner’s Guide
We stock and install Mr-Glass-compatible roofing components across Orlando, with most replacement parts running $400 to $1,800 installed depending on what failed and how much of the roof surface it affects. If you’ve spotted a crack, a leak, or daylight coming through a panel, we can usually get a technician out the same week with the right part on the truck. Most Orlando homeowners discover a Mr-Glass roofing failure the hard way: a water stain on the ceiling after an afternoon thunderstorm, or a brittle panel that snapped during a wind gust.
Mr-Glass roofing panels and skylight systems are common on Orlando homes built in the 1980s through the early 2000s, especially in College Park, Conway, and the neighborhoods around Lake Underhill. The Florida sun does not negotiate with plastic and polycarbonate. After 15 to 25 years, UV exposure turns panels brittle, seals shrink and crack, and the aluminum framing corrodes where salt air and humidity sit against the metal. Luca Romano has pulled enough failed Mr-Glass panels off Orlando roofs to know exactly what fails first and what is still holding up fine underneath. Good work doesn’t need a speech, it just needs to hold up.
Key Takeaways
- Mr-Glass roofing replacement in Orlando typically runs $400 to $1,800 installed depending on the panel type and framing condition.
- We stock common Mr-Glass panel sizes and seal kits on our trucks, which means fewer trips and a faster fix.
- DIY panel swaps go wrong fast on Orlando roofs with any pitch steeper than about 3/12. We cover that honestly below.
- We are an independent contractor, not affiliated with Mr-Glass. We install Mr-Glass-compatible parts sourced to OEM or better spec.
Which Mr-Glass Models This Applies To
Mr-Glass produced two main roofing product lines you’ll still find on Orlando homes: the Mr-Glass glazed patio roof system and the Mr-Glass skylight and ridge-light line. The patio roof system uses fixed or operable polycarbonate or acrylic glazing panels held in aluminum extrusions, typically in widths of 24, 36, or 48 inches. The skylight line includes flat and domed units in standard curb-mount and self-flashing configurations, with rough openings most commonly 22 1/2 by 22 1/2, 22 1/2 by 46 1/2, or 30 by 30 inches.
Before you order anything, check the underside of the panel or the frame rail. Mr-Glass stamped a series code plus the panel dimensions into the aluminum on most units made after the mid-1980s. If the stamp is gone, measure the exposed glazing width between the frame lips, not edge to edge on the frame. That measurement is the number that determines which replacement panel or seal kit fits. One compatibility gotcha we see constantly: older Mr-Glass patio roofs used a narrow-groove extrusion that will not accept modern thick-wall polycarbonate without a conversion gasket. If someone sells you a generic panel and skips that gasket, the first hard rain leaks at the seam. We carry both the standard and narrow-groove gasket sets so the panel actually seats the way Mr-Glass designed it.
For OEM versus aftermarket: Mr-Glass original replacement panels are still available for many models, but lead times run long and pricing is inconsistent. A quality aftermarket polycarbonate panel with the same light transmission rating and thickness spec often outperforms the original, especially the newer UV-capped multiwall sheets that hold up better under Florida sun than the solid acrylic used in the 1990s. We match the spec, not the brand loyalty. If OEM is what you want and it is still made, we order it and install it. If aftermarket gets you a better product faster, we tell you that too.
Styles & brands we work with
Signs Your Mr-Glass Roofing Is Failing
- Yellowing or clouding on the panel surface. This is UV degradation of the acrylic or polycarbonate. The panel loses structural strength long before it looks bad, so by the time it is yellow, it is close to cracking. In Orlando, panels facing south or west degrade noticeably faster than north-facing runs.
- Water stains on the ceiling or walls under the panel run. The usual cause is a failed seam gasket or a dried-out seal at the frame-to-flashing junction. Mr-Glass glazing gaskets shrink over time and pull back from the frame lip, creating a channel that feeds water directly into the ceiling cavity.
- A crack that runs between frame rails. Thermal expansion and contraction, plus the weight of standing water after a downpour, will eventually crack a panel that has lost flexibility. Once a crack starts, it spreads along the extrusion line because every temperature swing works the fracture.
- Bowing or sagging between supports. On longer Mr-Glass runs, the panel spans between aluminum rafters. When the panel sags and holds water, it means the glazing has softened from heat cycling. That ponding water adds live load the frame was never meant to carry.
- Condensation trapped inside a multiwall panel. If your Mr-Glass panel is the twin-wall or triple-wall polycarbonate type and you see moisture between the walls, the edge seal has failed. You cannot dry it out. The panel insulates poorly once water is inside, and it will eventually grow algae that you can see from below.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Orlando, Mr-Glass roofing replacement work lands between $400 and $1,800 installed. On the low end, you are replacing one or two small panels with standard glazing and the existing frame is in good shape. On the high end, you are replacing multiple panels, re-gasketing the full run, and rebuilding corroded frame sections or flashing. The parts themselves are not the expensive part of the job. The labor to safely remove the old glazing, prep the frame, seat the new panels correctly, and waterproof every seam is where the cost goes.
Here’s how that breaks down in the Orlando market:
Mr-Glass Roofing Repair Cost in Orlando, FL
| Scope of Work | Typical Installed Price |
|---|---|
| Single panel replacement, standard size | $400 – $800 |
| Full seal and gasket replacement, single run | $500 – $1,200 |
| Multiple panel replacement with frame repair | $1,000 – $1,800 |
| Full re-glaze of a large patio roof system | $1,800+ depending on square footage |
Every quote includes the part, the labor, the sealants and gaskets, haul-off of the old material, and cleanup. We walk you through the written price before a single panel comes off the roof, so the number you approve is the number on the invoice. And the work is covered by our 365-Day Done Right Promise: if the repair fails within a year, we come back and make it right. That is in writing, on every job.
DIY or Call Us?
What you can safely do yourself: inspect the panel surface for cracks and yellowing, check for water stains inside, and clear debris off the panels so water drains the way it should. A hose test on a dry day will also show you where water is getting in, which helps us diagnose faster when you call.
What you should not do yourself is climb onto an Orlando roof to swap a Mr-Glass panel. These panels are often on patio roofs with pitches steeper than they look from the ground, and the older polycarbonate gets slippery when even slightly damp. Falls from first-story roof edges are the most common serious injury we see in this trade. Beyond the fall risk, reseating a panel correctly means getting the gasket compression right, the weep channels clear, and the flashing lapped the right direction. Get any of that wrong and the leak comes back worse than before. If you want it done once and done right, call us at (850) 809-0306 for a free estimate. We’ll inspect the roof, identify the exact Mr-Glass part, and give you a written price before we touch anything.
FAQs
Mr-Glass panels in Orlando typically last 15 to 25 years before UV degradation makes them brittle enough to fail. South- and west-facing panels on full-sun exposures trend toward the shorter end of that range, while shaded or north-facing runs can go longer. Call (850) 809-0306 and we’ll tell you honestly whether the rest of your run has life left in it or whether it is time to plan a full re-glaze.
Small scratches and surface haze can sometimes be polished, but any crack, through-hole, or internal moisture inside a multiwall panel means replacement. Cracks in glazing cannot be reliably bonded, especially in Florida where thermal cycling works every repair loose. Call us at (850) 809-0306 and we’ll tell you which camp your panel falls in before you spend anything.
Most single-panel replacements on a Mr-Glass roof take half a day to a full day including sealant cure time. Full re-glazes of larger patio roof systems run two to three days depending on frame condition. Call (850) 809-0306 for a schedule estimate on your specific roof.
We stock the most common Mr-Glass panel widths, gasket profiles, and seal kits on our trucks in Orlando, so most repairs do not require a second trip or a wait on shipping. If your roof needs a less common size, we order it and install it as soon as it lands. Call (850) 809-0306 and we’ll check our stock while you’re on the phone.
Written by Luca Romano, Owner & Lead Contractor, Sawyer Remodel Orlando at Sawyer Remodel Orlando, serving Orlando and nearby areas.
