Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Orlando Homeowners Choose Mr-Glass Construction
We provide independent Mr Glass in Orlando construction service, from sliding patio door roller replacements to full frameless shower enclosure installs. Our crews work on Mr-Glass doors, windows, and enclosures nearly every week, so we know their frame tolerances, roller specs, and glass attachment methods well enough to service them correctly without factory training. Sawyer Remodel Orlando is not affiliated with or authorized by Mr-Glass. We’re an independent service provider, and that independence means we tell you straight when a repair makes sense and when replacement is the smarter money. Call (850) 809-0306 for a free estimate on any Mr-Glass work in the Orlando area.
Why Trust Sawyer Remodel Orlando for Your Mr-Glass Construction?
Mr-Glass products are built to tight tolerances, and servicing them correctly depends on understanding those tolerances. Our Orlando technicians have pulled apart enough 5900 Series doors and 7600 Series windows to know exactly which parts wear first in this climate. Luca Romano, owner and lead contractor at Sawyer Remodel Orlando, grew up in Los Angeles swinging a framing hammer before he could drive, trained in finish carpentry and structural work at Los Angeles Trade-Technical College, and has spent the better part of two decades putting that foundation to use across Central Florida. When a Mr-Glass door in College Park drags or a shower enclosure in Thornton Park wobbles, we already know why before we show up for Mr Glass service in Winter Park or nearby neighborhoods. We use Mr-Glass OEM replacement rollers, hinges, and sweeps whenever available because aftermarket copies often don’t match the original track or glass profile. Good work doesn’t need a speech – it just needs to hold up.
Styles & brands we work with
Common Mr-Glass Construction Problems We Fix in Orlando
- 5900 Series Sliding Patio Door – flat rollers and dragging. The rollers on these doors wear flat over time, and Orlando’s humidity plus pollen grit accelerates the problem. Once the rollers flatten, the door drags across the track and feels like it’s fighting you. We replace both roller assemblies, clean the track, and adjust the strike so the door closes flush against the weatherstrip.
- 7600 Series Single-Hung Window – clogged weep holes and sill rot. Weep holes on these windows are small, and Orlando’s summer downpours push water into them along with dust and pollen. When the weep holes clog, water sits in the sill channel and eventually rots the wood or stains the drywall below. We clear the weep holes, repair the sill if needed, and verify drainage before we call it done.
- 8200 Series Frameless Shower Enclosure – loose clamp brackets. Daily thermal cycling, hot shower steam against cooler glass, gradually loosens the clamp brackets on these enclosures. The glass panel starts to wobble, and if left alone, the panel can shift out of alignment and leak at the bottom corners. We tighten and re-secure the clamps, check the sweep, and reset the panel so it sits square.
- 400 Series Storefront Door – sagging pivot hinges. These doors are common on Orlando retail storefronts and office entries, and they see heavy traffic. The pivot hinges sag under repeated use, which makes the door scrape the threshold and throw off the closer. We replace worn pivots, realign the door leaf, and restore full swing clearance.
- Frameless shower and tub-to-shower conversion leaks. Leaks at the bottom corners of a Mr-Glass tub-to-shower conversion usually trace back to two things: a failed silicone bead or a slightly out-of-square frame. We remove the old bead, check the frame for square, and reapply a mildew-resistant sealant rated for wet areas.
Mr-Glass Parts & Our Repair-vs-Replace Approach
When we open up a Mr-Glass door or window, we check what’s actually worn before we order anything. We use Mr-Glass OEM replacement rollers, hinges, sweeps, and strike plates whenever they’re available. Aftermarket copies are cheaper, but they often don’t match the original track profile or glass thickness, which means a repair that should last years starts failing in months. If a Mr-Glass frame is bent or the glass is delaminating, we tell the customer straight that replacement is usually cheaper than repairing. For enclosures, we stock common clamp brackets and sweeps locally so most Orlando calls don’t wait on a parts order. Call (850) 809-0306 if you’re not sure whether your Mr-Glass issue is a repair or a replacement job – we’ll give you a straight answer and a written price.
Our Mr-Glass Service Process – Step by Step
- 1
Diagnosis with the door or window in front of us. We don’t quote over the phone without seeing the actual Mr-Glass product. The first step is a site visit in the Orlando area where we measure, check the track, rollers, hinges, and seals, and identify the exact failure point.
- 2
Written repair plan with a price you approve first. Before we pick up a tool, we hand you a written price for parts and labor. The number on the invoice is the number you approved. No change orders, no surprises.
- 3
Repair or installation using OEM parts whenever available. We install the right Mr-Glass OEM part, or a quality aftermarket match if OEM is discontinued, and we torque, align, and adjust everything to factory spec.
- 4
We test the full range of motion and drainage. After the repair, we run the door or window through its full cycle multiple times. We check drainage on windows, alignment on doors, and seal integrity on enclosures.
- 5
365-Day Done Right Promise in writing. If the repair fails within a year, we come back and make it right. That’s not a verbal promise – it’s written on every job.
See the difference
Before
After
Before
After
Before
AfterMr-Glass Products We Service & Install in Orlando
We service and install the Mr-Glass 5900 Series Sliding Patio Door, the 7600 Series Single-Hung Window, the 8200 Series Frameless Shower Enclosure, and the 400 Series Storefront Door. For enclosures and conversions, we also install new frameless glass shower enclosures and complete tub-to-shower conversions with Mr-Glass glass. Our Orlando inventory includes commonly needed rollers, hinge sets, sweeps, and clamp brackets for these series, which keeps most repairs moving without a long parts wait.
We Also Service These Brands
Sawyer Remodel Orlando isn’t tied to one manufacturer, but we are a licensed General Contractor. We work with KraftMaid cabinetry, Cambria and Silestone countertops, and Kohler fixtures on full kitchen and bath remodels across Orlando. If your Mr-Glass enclosure needs a new Kohler valve or Cambria threshold to complete the job, we handle that in-house.
FAQs – Mr-Glass Construction Service in Orlando
The most common cause is a worn bottom roller assembly that no longer sits fully in the track groove. When the roller flattens or the bearing seizes, the door rides higher on one side and can hop the track. Orlando’s sand and pollen grit makes this worse by grinding down the roller surface faster. We replace both roller assemblies with Mr-Glass OEM parts and adjust the strike so the door seats properly. Call (850) 809-0306 for a roller replacement quote – we’ll give you an exact price before any work starts.
Yes, in most Orlando bathrooms we can install a Mr-Glass 8200 Series frameless enclosure without pulling existing tile. The clamp brackets mount to the tile surface, not through it, so the tile stays intact. We check the tile for soundness and the walls for square before measuring. If the tile is loose or the walls are out of square beyond what clamps can absorb, we’ll tell you before we order glass.
Condensation between the panes means the insulated glass unit’s seal has failed. There’s no repair that restores a failed seal – the glass unit needs to be replaced. For the 7600 Series, the sash is designed to accept a replacement insulated glass unit, so in many cases you don’t need to replace the whole window frame. We measure the sash, order the correct replacement IGU, and swap it out on-site. Call (850) 809-0306 and we’ll tell you whether your sash can be reglazed or if a full window replacement is the better value.
In nearly every case we see in Orlando, the leak traces to a failed silicone bead at the corner joint, or a frame that’s slightly out of square. When the frame shifts even a few millimeters, the glass pulls away from the seal and water finds the gap. We strip the old bead, check the frame for square, shim if needed, and reapply a mildew-resistant silicone rated for wet areas. The fix usually takes under two hours.
We do. Our crews work on Mr-Glass 400 Series storefront doors across the Orlando metro, from retail shops in Thornton Park to office entries in Lake Nona and Mr Glass in Casselberry. The most common call is a sagging pivot hinge that makes the door scrape the threshold. We replace the pivots, realign the leaf, and check the closer so the door swings and latches correctly. We can schedule around your business hours to minimize downtime.
How much does Mr-Glass construction cost in Orlando?
| Service | Orlando Market Price Range |
|---|---|
| Mr-Glass 5900 sliding door roller replacement | $400 – $900 |
| Mr-Glass 7600 window sill repair and weep hole clearing | $300 – $800 |
| Frameless glass shower enclosure installation | $4,500 – $12,000 |
| Tub-to-shower conversion (with Mr-Glass glass) | $3,500 – $10,000 |
These ranges cover typical Orlando jobs. Your exact price depends on the condition of the existing frame, the size of the glass, and access. We give you a written line-item price before any work starts, so the number you approve is the number on the invoice. Call (850) 809-0306 for an exact quote – estimates are free.
Book Your Mr-Glass Service in Orlando, FL
Whether it’s a dragging 5900 slider in College Park or a wobbly 8200 enclosure in Lake Nona, our Orlando crews are ready to service your Mr-Glass product with OEM parts and a written price before the work begins. Call (850) 809-0306 to schedule your free estimate.
Written by Luca Romano, Owner and Lead Contractor at Sawyer Remodel Orlando, serving Orlando since 2005.
