Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Kitchen Remodeling: The Orlando Owner’s Guide
A full Tamko kitchen remodel in Orlando typically runs $14,000 to $45,000 installed, depending on cabinet layout, countertop material, and whether you’re moving plumbing or electrical. We stock Tamko-compatible cabinet components, trim, and hardware on our trucks, and most partial replacements like a failed cabinet face frame or delaminated door can be matched and installed within days of your call. Most Orlando homeowners discover a problem the same way: a drawer front pulls loose in the humid summer months, or a cabinet box starts sagging after years of Florida moisture cycles.
Tamko built a reputation for value-priced kitchen cabinetry that holds up reasonably well in dry climates. Orlando’s humidity is a different animal. We see the same failure patterns across College Park, Winter Park, and Dr. Phillips: doors swelling at the seams, laminate peeling at the bottom edges, and particleboard boxes losing their structural integrity where sink moisture wicks upward. That’s not a knock on Tamko, it’s just physics in a subtropical environment. The good news is we can rebuild, reface, or replace the failed components without tearing out the entire kitchen if the boxes are still sound.
Key takeaways:
- Typical Tamko kitchen remodel in Orlando: $14,000 to $45,000 installed
- Partial component replacement costs far less, starting around $2,000 to $4,000 for a cabinet reface or door swap
- We stock Tamko-compatible hinges, drawer slides, and trim on the truck
- Written price before any work starts, same number on the invoice
Which Tamko Models This Applies To
Tamko has produced several cabinet lines over the years, and compatibility can trip up even experienced Orlando handymen. The big gotcha: Tamko’s newer lines use a 35mm cup hinge spacing that matches European standards, while their mid-2000s production used a 26mm offset that’s no longer made. If you order the wrong hinge, the door won’t sit flush no matter how much you adjust it. We carry both specifications in our Orlando shop because we’ve been burned by this before and made sure it doesn’t happen again.
Identifying your Tamko cabinet generation starts with the drawer box. Older Tamko boxes use a stapled particleboard construction with a white vinyl interior. The newer series, mostly post-2012, uses dovetail joinery on drawers and upgraded soft-close slides. Check the inside of a drawer or the back of a door for a small paper label or ink stamp. If the label is gone, measure the hinge cup: 35mm means newer production, 26mm means mid-2000s. When we reface a Tamko kitchen, we use OEM hardware where it’s still available and quality aftermarket equivalents like Blum hinges and Grass slides where OEM parts have been discontinued. The aftermarket parts frequently outlast the originals, especially in Florida humidity.
Styles & brands we work with
Signs Your Tamko Kitchen Remodeling Is Failing
- Doors that won’t stay closed or won’t close straight. This is almost always a hinge failure. Tamko hinges from the mid-2000s era have a thin metal clip that fatigues and breaks. We replace these with Blum hinges that are rated for far more cycles than the original equipment.
- Swollen or darkened cabinet bottoms under the sink. Water wicks up from the sink deck into the particleboard box. In Orlando’s humidity, that moisture never fully dries. The box starts to crumble, and the face frame separates. This is a box replacement situation, and it’s one of the most common Tamko repairs we do in Orlando.
- Laminate peeling or bubbling on door edges. Heat and humidity cause the contact adhesive Tamko used on older lines to break down. Once the laminate lifts, it snags on clothing and gets worse fast. A reface with proper wood veneer or thermofoil replacement panels solves it permanently.
- Drawers that grind, stick, or drop on one side. The original Tamko drawer slides wear out asymmetrically, especially in kitchens where the sink-side drawers catch more water exposure. The metal corrodes under the vinyl coating and the ball bearings seize. We swap in soft-close Grass slides that are rated for wet environments.
- Cabinet frame pulling away from the wall above the range. Heat rises from cooking, dries the backing boards, and loosens the mechanical fasteners Tamko used at the factory. If you can see daylight between the cabinet and the wall, the attachment points are failing. This one needs attention before the cabinet drops onto your range.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what we tell Orlando homeowners outright, before they even book an estimate: a partial Tamko repair is not a $14,000 job. If the boxes are sound and you just need new doors, hinges, and drawer fronts, you’re looking at $4,000 to $8,000 depending on kitchen size and door style. A full reface with new cabinet boxes where needed and all new hardware runs $8,000 to $14,000 in Orlando. If the entire kitchen needs gutting and rebuilding with new Tamko-compatible or upgraded cabinet lines, that’s the $14,000 to $45,000 range, depending on whether you’re replacing countertops at the same time.
For comparison, here are the Orlando price ranges we work with on component work:
- Cabinet installation (new boxes, existing layout): $4,000 to $13,000
- Countertop installation (when Tamko cabients are being replaced or refaced): $2,000 to $6,500
- Cabinet reface (doors, drawer fronts, hardware, matching trim): $4,000 to $10,000
- Full kitchen remodel (Tamko-compatible cabinetry plus counters, backsplash, and installation): $14,000 to $45,000
Every quote includes the parts, the labor, the haul-away of old material, and a written price before we touch anything. The number on the invoice is the number you approved. That’s the Relay Visibility Guarantee, and it’s not optional when you work with us. Luca Romano runs every Orlando job under that standard, whether it’s a single drawer swap or a full kitchen rebuild.
DIY or Call Us?
You can safely check a few things before calling: whether hinges are bent or screws are stripped, whether drawer slides are visibly corroded, and whether the cabinet feels loose from the wall. Checking is fine. Re-hanging a Tamko door with a mismatched hinge is not fine, because you’ll drill new holes, weaken the frame, and turn a $200 hinge replacement into a $2,000 face frame repair. If a cabinet box is pulling away above your range, don’t climb up and start removing fasteners. That’s weight over a hot surface, and a falling cabinet can do real damage to you and your range. Call us.
The honest split is this: if you’re confident with a stud finder and a level, you can lube slides and tighten door screws. But once you’re dealing with moisture-swollen boxes, sagging corners, or failed attachment points behind the cabinet, you need someone who’s done this in Orlando’s climate for years. We have. Call (850) 809-0306 and we’ll give you a written estimate before any work starts.
FAQs
A Tamko kitchen installed correctly in Orlando lasts 12 to 20 years before showing meaningful wear, but that lifespan depends heavily on ventilation, humidity control, and whether the original installer sealed the sink base and used proper backing. Florida humidity cuts roughly five years off what the same cabinets would do in a dry climate. Call (850) 809-0306 if you want us to evaluate the specific condition of your doors and boxes, estimates are free.
Yes, in most Orlando homes we repair rather than replace: refacing doors, swapping hinges and slides, and rebuilding sink bases where water damage is localized. Full replacement only makes sense when the boxes themselves have lost structural integrity. We’ll tell you which situation you have and put it in writing before we do anything.
A drawer slide or hinge swap is same-visit work once we have your Tamko generation identified. A full reface or box rebuild runs 3 to 7 working days depending on door lead time and whether we’re painting on-site or using factory-finished thermofoil. We lock the schedule at the estimate and send photo updates before and after.
We stock Tamko-compatible hinges in both cup sizes, soft-close drawer slides, and matching trim profiles in our Orlando shop, and we can source OEM Tamko door and drawer fronts where the production line is still active. For discontinued Tamko parts we use Blum, Grass, and other aftermarket equivalents that match or exceed the original spec. Sawyer Remodel Orlando is an independent contractor and not affiliated with Tamko, which means we tell you when an aftermarket part is actually the better call and charge you the same written price either way.
Good work doesn’t need a speech, it just needs to hold up.
Written by Luca Romano, Owner & Lead Contractor, Sawyer Remodel Orlando at Sawyer Remodel Orlando, serving Orlando and nearby areas.
Ready to get your Tamko kitchen looking and working right? Call (850) 809-0306 for a free estimate. We answer live, 24/7, and you’ll get a written price before any work starts.
